It looks as if precise stone nevertheless saves money, time and labor. Stone veneer panels created from sturdy, lightweight polyurethane is the right supplies for a lot of initiatives inside and open air your individual residence or enterprise. And you do not need specific talents or devices to do the arrange your self. When you may have a measuring tape, a stage, and first woodworking devices like saws and drills, you’ll be able to do it. That is how.

Provides and Devices
o Stone veneer siding panels
o Constructing adhesive (PL® Polyurethane Premium actually helpful)
o Screws relevant in your arrange, as described inside the instructions beneath
o Filler or caulk to match the panels
o Screwdriver (cordless driver-drill actually helpful)
o Picket-cutting seen for chopping panels (jigsaw, bandsaw, and lots of others.)
o For arrange over concrete: Each a hammer drill and masonry bit; or, for adhesive-only arrange, Good Stuff(TM) Gaps & Cracks filler and disposable gloves

Instructions
1. Make certain the stone veneer panels will fill the height of the wall with out leaving a slim strip uncovered. For example, say your wall needs 4 rows of panels plus just one inch. Because of it’s onerous to cut and arrange a strip that slim, it’s essential to plan to cut an inch or two off the underside of the underside row of panels. Then the best row will doubtless be that loads wider and easier to work with.
2. Sweep or vacuum the wall to remove mud and free filth. For concrete, use a stiff broom or brush and sweep firmly.
3. Snap a stage line on the wall on the excessive of the first row of panels. If the panels will doubtless be scribed to the bottom, measure up from the lowest degree of the bottom. If any gap on the bottom will doubtless be hidden by trim, measure up from the highest degree of the bottom.
4. Decide the place the first panel ought to start by laying out some panels on the bottom alongside the wall. Or, measure the width of the wall and the width of a single panel, and do the construction on paper. Your goal is to steer clear of chopping very slim panels at each end of the wall. Perceive that you’re going to be staggering the rows of panels so their vertical seams do not line up.
5. Arrange the first panel of the underside row (scroll all the way in which all the way down to be taught half entitled “Placing in Each Stone Veneer Panel”). You probably can work from the left or correct, and you’ll start with the very end panel or the one subsequent to it. Everytime you do arrange an end panel, you may should scribe it to the adjoining wall ground (be taught last a part of this textual content, “Scribing Stone Veneer PanelsInstalling Each Stone Veneer Panel
Usually you make the most of every adhesive and screws to place in each stone veneer panel. In case you might be placing within the panels on concrete, you may in its place adjust to a novel method using adhesive solely.

Adhesive and Screws (any ground)
1. Choose flat-head Phillips screws relevant in your arrange:
o You need 4 screws per panel.
o For exterior installations, bear in mind to make use of exterior screws that won’t rust.
o For arrange into wood studs, use screws prolonged adequate to penetrate between 3/4 inch and 1 inch into the stud. Do not use longer screws; you’ll hit wires or pipes!
o For arrange over concrete, use Tapcon® concrete screws prolonged adequate to penetrate between 1 inch and 1 3/4 inch into the concrete.
2. Dry-fit the panel in place and guarantee it fits. In case you might be placing in on concrete, pre-drill a spot shut to each nook for the Tapcon screw. Observe the producer’s specification for the opening dimension.
3. Apply improvement adhesive in a zigzag pattern to the once more of the panel.
4. Apply adhesive to any edge that matches in direction of an current panel. Apply it so it ought to squeeze out in direction of the once more considerably than the doorway.
5. Slip the panel into place, interlocking the seams with adjoining panels. Use your hand or fist to faucet the panel so the seams are very tight.
6. Drive a screw into the panel shut to each nook, barely countersinking the screw head.

Adhesive Solely (completely different method for concrete)
1. Be taught the instructions on the can of Good Stuff Gaps & Cracks filler. Placed on disposable gloves; Good Stuff is very sticky.
2. Dry match the panel in place and guarantee it fits.
3. If this panel fits in direction of already-installed panels, apply improvement adhesive to those edges on the put in panels. Apply it so it ought to squeeze out in direction of the once more considerably than the doorway Clip on veneers.
4. Rigorously apply a zigzag snake of Good Stuff to the once more of the panel. Maintain numerous inches away from the edges, and don’t apply an extreme quantity of. The froth expands as a result of it cures.
5. Immediately slip the panel into place on the wall. Wiggle it barely to unfold the froth, and press it firmly in direction of adjoining panels so the seams are tight.
6. Keep the panel firmly in direction of the wall for a few minutes until the froth models. Make certain it’s firmly connected sooner than placing within the subsequent panel.

Scribing Stone Veneer Panels
Everytime you match a faux stone veneer panel in direction of a splendidly plumb adjoining wall or a splendidly stage flooring, all you must do is cut back the panel straight all through. However when the wall or flooring is irregular or out of sq., you must scribe the sting of the panel so it fits precisely with none ugly gaps.
These steps make clear scribing to a wall. Use a similar course of to scribe to a ceiling or flooring.
1. Set the compass unfold:
o In case you are placing within the first panel in a row, and the panel is already cut back to the right robust measurement, unfold the compass merely big adequate to cowl crucial gap between the wall and the robust part of the panel — say, 1/2 inch.
o In case you are turning into the last panel in a row, first cut back the panel an inch or two over-long. Keep it in place, stage and butted in direction of the wall, so it barely overlaps the next-to-last panel. Then unfold the compass to exactly match the amount of the overlap (not counting the interlocking tabs).
2. Rigorously preserve the panel in place, stage and butted in direction of the wall. With the compass pencil resting on the panel and the aim resting in direction of the wall, slide the compass so the pencil traces a line on the panel as the aim follows the contour of the wall.
3. Cut back fastidiously alongside the highway. Verify the match and use a tough file to remove any extreme spots.